6530A REV E Norge Washer Parts List

Surface element - 8 inch - 2600w (8 inch electric coil surface element with looped terminals, 2600 watts. 5 turns.)

This surface burner element is eight inches in diameter. It has five turns, 2600 watts and looped terminal ends. The element provides heat to the cooking surface on your range. If your element is not heating, you may need to replace this part. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part. It is sold individually.

Ice maker assembly - 8 cube (icemaker)

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

Temperature sensor (sensor temp fz)

The temperature sensor, also known as a thermistor, helps detect the temperature inside the refrigerator and sends the information to the control board. If your refrigerator is too warm or not cooling properly, you may need to replace the temperature sensor. This is a genuine OEM part. Please make sure to disconnect the power to the refrigerator before starting your repair.

Dishwasher dishrack rollers and axles (roller side)

This is a kit of 4 which includes the wheels and axels.

Refrigerator ice and water filter

Module shelf insert - clear (insert module)

This part is the front of the door shelf bin.

Idler pulley assembly

The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.

Refrigerator crisper drawer (pan-crisper)

The crisper drawer in your refrigerator is designed to control humidity and keep food fresh for as long as possible. These drawers get a lot of day-to-day use and they crack, warp, or stain over time. This is an official replacement part, it is clear plastic, and designed for side-by-side refrigerators. This repair is as simple as removing the old drawer, and lining the new drawer up with the existing tracks and sliding it into place. It is important to note that new pan does not have the humidity control slide, and this component is now sold separately.

Retaining ring

The retaining clip goes onto the end of the roller axle and holds the drum roller on to the axle. If the ring is broken or damaged, you will need to replace it. This is a genuine OEM part and is sold individually.

Drum glide (dryer drum glide pad. Drum glides help to support the front of the dryer drum as it rotates. If the drum glides are worn out, the dryer will be noisy.)

The drum glide helps the front drum rotate smoothly and quietly while operating. If your dryer will not tumble or is noisy, the glide could be worn down, causing metal on metal noise. In this case, it will need to be replaced. It is recommended to replace both glides at the same time and two are required for the dryer. The drum glide is a genuine OEM part and is sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Heating element (element)

The drum glide helps the front drum rotate smoothly and quietly while operating. If your dryer won’t tumble or is noisy, the glide could be worn down, causing a metal on metal noise. In this case it will need to be replaced. It is recommended to replace both glides at the same time and two is required for the dryer. The drum glide is a genuine OEM part and is sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Upper drum glide (drum glide - top)

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Rear drum bearing kit (shaft bracket asm)

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Drive motor with pulley (use wpl 279827)

This drive motor operates the dryer by turning the drive belt which spins the drum and will fit most Whirlpool incorporated dryer brands before 1996. If the motor has shorted out, it will no longer turn the drum and will need to be replaced. The drive motor includes the pulley that is not available separately. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Dual action agitator (agitator asm multi)

This plastic dual action agitator is white in color. It is approximately eighteen inches tall with a base diameter of about 12-1/4 inches. The agitator pivots back and forth, moving the clothes from the top to the bottom of the tub, through the detergent and water to wash them. If the agitator becomes damaged or will not agitate, you may need to replace the part. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.